![Weyl semimetal](/sites/default/files/styles/featured_square_large/public/2024-08/Picture4.jpg?h=b38bf506&itok=nYXXiLDs)
Filter News
Area of Research
News Topics
- (-) 3-D Printing/Advanced Manufacturing (3)
- (-) Bioenergy (1)
- (-) Biomedical (2)
- (-) Nanotechnology (3)
- (-) Neutron Science (4)
- (-) Physics (2)
- (-) Transportation (2)
- Chemical Sciences (1)
- Composites (2)
- Computer Science (1)
- Critical Materials (2)
- Energy Storage (1)
- Grid (1)
- Isotopes (4)
- Materials (1)
- Materials Science (3)
- Microscopy (2)
- Nuclear Energy (1)
- Partnerships (1)
- Polymers (2)
Media Contacts
![From left, ORNL’s Rick Lowden, Chris Bryan and Jim Kiggans were troubled that target discs of a material needed to produce Mo-99 using an accelerator could deform after irradiation and get stuck in their holder. From left, ORNL’s Rick Lowden, Chris Bryan and Jim Kiggans were troubled that target discs of a material needed to produce Mo-99 using an accelerator could deform after irradiation and get stuck in their holder.](/sites/default/files/styles/list_page_thumbnail/public/news/images/2018-P01734.jpg?itok=IbSUl9Vc)
“Made in the USA.” That can now be said of the radioactive isotope molybdenum-99 (Mo-99), last made in the United States in the late 1980s. Its short-lived decay product, technetium-99m (Tc-99m), is the most widely used radioisotope in medical diagnostic imaging. Tc-99m is best known ...
![From left, Andrew Lupini and Juan Carlos Idrobo use ORNL’s new monochromated, aberration-corrected scanning transmission electron microscope, a Nion HERMES to take the temperatures of materials at the nanoscale. Image credit: Oak Ridge National Laboratory From left, Andrew Lupini and Juan Carlos Idrobo use ORNL’s new monochromated, aberration-corrected scanning transmission electron microscope, a Nion HERMES to take the temperatures of materials at the nanoscale. Image credit: Oak Ridge National Laboratory](/sites/default/files/styles/list_page_thumbnail/public/news/images/2018-P00413.jpg?itok=UKejk7r2)
A scientific team led by the Department of Energy’s Oak Ridge National Laboratory has found a new way to take the local temperature of a material from an area about a billionth of a meter wide, or approximately 100,000 times thinner than a human hair. This discove...
![ORNL researchers Todd Toops, Charles Finney, and Melanie DeBusk (left to right) hold an example of a particulate filter used to collect harmful emissions in vehicles. ORNL researchers Todd Toops, Charles Finney, and Melanie DeBusk (left to right) hold an example of a particulate filter used to collect harmful emissions in vehicles.](/sites/default/files/styles/list_page_thumbnail/public/news/images/CG-1D%20user%20-%20ETSD_Toops-2878R_r1.jpg?itok=sRbVXIkF)
Researchers are looking to neutrons for new ways to save fuel during the operation of filters that clean the soot, or carbon and ash-based particulate matter, emitted by vehicles. A team of researchers from the Energy and Transportation Science Division at the Department of En...
![This isotropic, neodymium-iron-boron bonded permanent magnet was 3D-printed at DOE’s Manufacturing Demonstration Facility at Oak Ridge National Laboratory. This isotropic, neodymium-iron-boron bonded permanent magnet was 3D-printed at DOE’s Manufacturing Demonstration Facility at Oak Ridge National Laboratory.](/sites/default/files/styles/list_page_thumbnail/public/3Dprintedmagnet_image1_0.jpg?itok=uHDlDr_T)
Researchers at the Department of Energy’s Oak Ridge National Laboratory have demonstrated that permanent magnets produced by additive manufacturing can outperform bonded magnets made using traditional techniques while conserving critical materials. Scientists fabric...